You're viewing a previously published revision of this guide.  View latest revision

Older
Oct 01, 2021 - 11:10:35
Oct 02, 2021 - 12:10:12 Oct 02, 2021 - 12:10:57 Oct 02, 2021 - 12:10:41 Oct 02, 2021 - 12:10:20 Oct 02, 2021 - 12:10:50 Oct 02, 2021 - 12:10:01 Oct 02, 2021 - 12:10:17 Oct 02, 2021 - 12:10:32 Oct 02, 2021 - 12:10:13 Oct 02, 2021 - 12:10:54 Oct 02, 2021 - 12:10:18 Oct 02, 2021 - 12:10:24 Oct 02, 2021 - 12:10:18 Oct 02, 2021 - 12:10:04 Oct 02, 2021 - 12:10:23 Oct 02, 2021 - 12:10:58 Oct 02, 2021 - 12:10:51 Oct 01, 2021 - 11:10:58 Oct 01, 2021 - 11:10:52 Oct 01, 2021 - 11:10:53 Oct 01, 2021 - 11:10:17 Oct 01, 2021 - 11:10:17 Oct 01, 2021 - 11:10:08 Oct 01, 2021 - 11:10:26 Oct 01, 2021 - 11:10:16 Oct 01, 2021 - 11:10:22 Oct 01, 2021 - 11:10:35 Oct 01, 2021 - 11:10:23 Oct 01, 2021 - 11:10:15 Oct 01, 2021 - 10:10:57 Oct 01, 2021 - 10:10:31 Oct 01, 2021 - 10:10:15 Oct 01, 2021 - 10:10:30
Newer

µClouds SE Assembly Template Instructions

Written By: Daniel Gilbert
  • Comments: 0
  • Favorites: 0

Difficulty

Moderate

Steps

2

Time Required

Suggest a time??

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Private

Private

This guide will not appear in search results and can only be viewed by team members!

  1. This step only needs to be done once. The standoffs can remain attached to the template permanently for subsequent iterations. Identify the green Assembly Template. It has the part number TD-UCSE-D-AT printed on it. Note the orientation of the board. The standoffs will be installed on the side that has THIS SIDE FACES DOWN printed on it.

    • This step only needs to be done once. The standoffs can remain attached to the template permanently for subsequent iterations.

    • Identify the green Assembly Template. It has the part number TD-UCSE-D-AT printed on it.

    • Note the orientation of the board. The standoffs will be installed on the side that has THIS SIDE FACES DOWN printed on it.

    • Locate two M2.5 × 10 mm female standoffs.

    • Secure each standoff using one M2.5 × 6 mm pan head machine screw in each of the two locations shown.

    • Flip over the completed Assembly Template. It is now ready to be used.

  2. Identify the Control Board assembly. It has part number TD-UCSE-D-CB printed on its bottom side. For ease of access to the solder pads, it is highly recommended to solder through-hole components H1, H2, H3, and H4 before continuing this process.

    • Identify the Control Board assembly. It has part number TD-UCSE-D-CB printed on its bottom side.

    • For ease of access to the solder pads, it is highly recommended to solder through-hole components H1, H2, H3, and H4 before continuing this process.

    • Do not solder any of the following components yet.

    • Place the PCB spacer onto component S1, then place component S1 onto the board.

    • Place the spacer components DS1-4 onto components D1-4, then place components D1-4 onto the board.

Author

Daniel Gilbert

Member since: 12/07/2019

1,935 Reputation

8 Guides authored